SAFETY SOLVENT DEGREASER
NON-FLAMMABLE, VOC-FREE, EASILY BIODEGRADABLE
CERTIFIED NSF K1 FOR FOODSTUFFS INDUSTRIES (IAA)
ESTER-REINFORCED DEGREASING POWER
PLANT-BASED
USABLE COLD AND HOT
"SPECIAL FORMULA FOR DEGREASING PARTS WASHERS"
|
|
|
|
Solvent without COV |
.jpg)
TECHNICAL FLUID MADE OF PLANT-BASED ESTERS
HIGH-PERFORMANCE SOLVENT DEGREASER
SPECIAL FORMULA FOR PARTS WASHERS, STRUCTURES, NETWORKS, TANKS, PANS, INDUSTRIAL MAINTENANCE
Usable cold or in baths up to 70°C.
Declassification of ATEX zones.
Very high solvent power KB index greater than 50.
Dielectric, breakdown voltage IEC 156 50,000 volts
Immediately dissolves tar, crude oil, heavy hydrocarbons,
combustion residue, greases, lubricants.
Formulated with additives to accelerate settling
in solvent parts washers
SMP optimisation
Solvent Management Plan
(IED Directive)
Solvent input/output material balance
Low volatility, reduction of consumption.
ELIMINATION OF SOLVENT EMISSIONS
|
ODP 0 |
PRP 0 |
Freezing point -20°C. Outdoor storage is authorised.
Reduction of industrial risk, operating loss, third-party liability
(insurance code)
DESCRIPTION
Solvent degreaser, non-flammable safety cleaning agent, biodegradable, VOC-free, with very high solvent power, specially formulated for use in solvent parts washers, technical fluid using agrobased plant esters also usable for all manual degreasing operations with or without mechanical action or by immersion in cold or hot baths up to 70°C.
USER PRECAUTIONS
NEUTRALENE® BIO 1000 does not pose any particular hazard except in the very rare cases of accidental ingestion. Refer to the material safety data sheet for the recommendations on storage, use, and disposal.
PHYSICO-CHEMICAL PROPERTIES
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Appearance |
Visual |
Fluid |
- |
|
Colour* |
Visual |
Colourless |
- |
|
Smell |
Olfactory |
Very weak |
- |
|
Density at 25°C |
NF EN ISO 12185 |
805 |
kg/m3 |
|
Refraction index |
ISO 5661 |
1.4470 |
- |
|
Freezing point |
ISO 3016 |
<-20 |
°C |
|
Water solubility |
- |
Insoluble |
% |
|
Kinematic viscosity at 40°C |
NF EN 3104 |
2.5 |
mm²/s |
|
Acid index |
EN 14104 |
<0.1 |
mg(KOH)/g |
|
Iodine index |
NF EN 14111 |
0 |
gI2/100g |
|
Water content |
NF ISO 6296 |
<0.001 |
% |
|
Residue after evaporation |
NF T 30-084 |
0.0 |
% |
|
Steam pressure at 20°C |
NF EN 13016-1 |
<0.1 |
hPa |
|
PERFORMANCE PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
KB index |
ASTM D 1133 |
>70 |
- |
|
Evaporation speed |
- |
>4 |
h |
|
Surface tension at 20°C |
ISO 6295 |
28 |
dyne/cm |
|
Breakdown voltage |
IEC.156 |
50,000 |
Volts |
|
Copper blade corrosion 100 h at 40°C |
ISO 2160 |
1a |
Measured value |
|
FIRE SAFETY PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Flashpoint (closed tank) |
ISO 2719 |
>100 |
°C |
|
Self-combustion point |
ASTM E 659 |
>230 |
°C |
|
Lower Explosive Limit |
NF EN 1839 |
0.6 |
% (volume) |
|
Upper Explosive Limit |
NF EN 1839 |
6.5 |
% (volume) |
|
Explosive, oxidising agent, flammable, highly or extremely flammable substance content |
CLP Regulation |
0 |
% |
|
TOXICOLOGICAL PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Anisidine index |
NF ISO 6885 |
<1 |
- |
|
Peroxide index |
NF ISO 3960 |
<1 |
meq(O2)/kg |
|
TOTOX (anisidine index+2x peroxide index) |
- |
<3 |
- |
|
CMR, irritant and corrosive substance content |
CLP Regulation |
0 |
% |
|
Residual methanol content from transesterification |
GC-MS |
0.0 |
% |
|
Emissions of hazardous compounds, CMR, irritants, corrosive at 160°C |
GC-MS |
0 |
% |
|
ENVIRONMENTAL PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Biodegradability |
OECD 301 A/C |
>80, >90 |
% |
|
Steam pressure at 20°C |
- |
<0.1 |
hPa |
|
VOC content (Volatile Organic Compounds) |
- |
0 |
% |
|
Sulphur content |
GC MS |
0 |
% |
|
Benzene content |
ASTM D6229 |
0 |
% |
|
Total halogen content |
GC MS |
0 |
% |
|
Chlorinated solvent content |
- |
0 |
% |
|
Aromatic solvent content |
- |
<0.01 |
% |
|
Environmentally-hazardous substance content |
CLP Regulation |
0 |
% |
|
Content of compounds with GWP |
- |
0 |
% |
|
Content of compounds with ODP |
- |
0 |
% |
|
Carbon assessment, life cycles analysis. |
ISO 14040 |
1.55 |
Kg carbon equivalent |
* nm: not measured or not measurable
|
ADDITIONAL PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Aniline point |
ASTM D 611 |
80 |
°C |
|
Bioaccumulation n-octanol-water ratio |
OECD 107 |
<3 |
logKow |
|
Hazard classification for water |
WGK |
1 |
Class |
PRESENTATIONS
|
IBC GRV 1000 L
|
Drum 200 L
|
Can 20 L
|
Product for the food industry (IAA)
Using an HACCP approach or method
Analysis of dangers and critical points to control them
ISO 22 000 CODEX ALIMENTARIUS
Category NSF:
K1 solvent: usable outside food manufacturing areas (the vapours must not enter the manufacturing area) to degrease equipment (e.g. conveyor bearings, maintenance of other mechanical components, etc.) used in manufacturing areas.
INSTRUCTIONS FOR USE
|
|
|
|
Degreasing with rag |
Degreasing with brush |
 |
|
|
Low-pressure sprayers with water rinse
|
Solvent parts washers |
|
|
|
|
Ultrasound tanks
|
Hot or cold immersion tanks |
 |
 |
|
Rotating or forward-travelling basket |
A3 washing machines |
Looking for another product?
|
Discover our entire IAA range by clicking on the photo |
Manufacturing, lubrification, cleansing, protection,
IBiotec® Tec Industries® Service
offers a wide range of products reserved for industrial area
If you wish for :
a free sample
a technical advice
a product data sheet
a safety data sheet
IBiotec® Tec Industries®Service
manufacturer of technical chemical products.
Welcome to our website.
IBiotec® Tec Industries®Service is on : 